4 1/4 inch (108 mm) drill-center pulls for medium drawer fronts
4 1/4 inch (108 mm) drill-center pulls fall between the standard 4 inch and 5 inch sizes. The 108 mm spacing is less common than its neighbors but shows up in specific manufacturer lines, particularly some European and high-end American brands that use it as a deliberate intermediate proportion. Drawer fronts roughly 16 to 22 inches wide are the typical fit. Specifiers working on custom kitchens reach for this size when the standard 4 inch and 5 inch options feel slightly off against a particular drawer width.
Where 4 1/4 inch fits
Mid-size base cabinet drawers in transitional kitchens. Bath vanity drawers in the larger primary-bath range. Some designer cabinetry runs that use 4 1/4 inch as the intermediate spacing between an island pull at 5 inch and a perimeter cabinet pull at 4 inch. The size carries a small but well-defined catalog. Custom built-in office furniture with mid-width lateral file drawers also lands here when the design specifies a precise intermediate proportion.
What hardware looks like at this size
Bar pulls and T-pulls dominate. A handful of decorative pulls with backplates. Cup pulls thin out at this length, since most cup-pull catalogs go from 2 1/2 inch to 3 inch and then jump to 4 inch. Pulls offered at 4 1/4 inch usually come from brands that produce a continuous size range rather than the standard step pattern. The finish catalog leans modern, with the strongest selection in brushed nickel, matte black, satin brass, and aged bronze.
Adjacent sizes worth comparing
Below is 4 inch (101.6 mm). Above is 5 inch (127 mm). For the standard transitional pull size, see 3 3/4 inch (95.2 mm).
Frequently Asked Questions
What is 4 1/4 inch in millimeters, and how do I confirm my existing holes match this spacing?
4 1/4 inches converts to exactly 108 mm center-to-center. To measure existing holes, place a ruler at the center of one screw hole and measure straight across to the center of the second hole — not edge-to-edge. A measurement of 108 mm (approximately 4.25 inches) confirms this drill-center spec and means a direct replacement pull will drop in without drilling.
What drawer front widths suit a 4 1/4 inch (108 mm) pull?
Drawer fronts roughly 16 to 22 inches wide are the typical fit for a 108 mm drill-center pull. The pull should span no more than about half to two-thirds of the drawer front width so it reads as proportional rather than cramped or oversized. This range covers mid-size base cabinet drawers, bath vanity drawers in a larger primary-bath configuration, and mid-width lateral file drawers in custom built-in office furniture.
How does the 4 1/4 inch (108 mm) size compare to the adjacent 4 inch and 5 inch drill-center options?
The 4 inch (101.6 mm) and 5 inch (127 mm) sizes are the far more common catalog entries and typically offer a broader selection of styles and finishes. The 4 1/4 inch (108 mm) sits as a deliberate intermediate — used when 4 inch feels slightly small and 5 inch feels slightly large against a specific drawer width. It appears primarily in European and high-end American brands that run continuous size ranges rather than the standard step pattern, so the available catalog is smaller but purposeful.
What pull styles are available at 4 1/4 inch (108 mm), and are there any notable gaps?
Bar pulls and T-pulls represent the dominant styles at this drill-center spacing, along with a handful of decorative pulls with backplates. Cup pulls are largely absent at this size — most cup-pull catalogs jump from 3 inch directly to 4 inch, bypassing 108 mm entirely. The finish selection leans modern, with the strongest availability in brushed nickel, matte black, satin brass, and aged bronze.
What Customers Say
Trusted by thousands of designers, builders, and homeowners
Kayla Malo is the most attentive and super human ever! My experience with this company is stellar!
Love working with Kayla, she is extremely helpful and quick with responding to my questions!
Kayla was GREAT!!!! Super help and fast answers. One of the best I've ever dealt with.